EN 10219 S460MH Steel Pipe: Selection & Application

Views : 432
Author : admin
Update time : 2026-10-22 08:37:16

       EN 10219-1 is the European standard for cold-formed welded structural hollow sections. S460 is the high-strength grade within this standard. The “S” stands for structural steel, “460” means a minimum yield strength of 460 MPa, “M” means thermomechanical rolling, and “H” means hollow section.Shengtian Group this guide covers S460MH under EN 10219-1, as well as S460NH and S460NLH under EN 10210. You will find material data, size ranges, selection logic, driving suitability, and certification requirements.

  The S460 material series has three main grades:

  ● S460MH — cold-formed, TMCP, impact tested at -40°C

  ● S460NH — hot-formed, normalized, impact tested at -20°C

  ● S460NLH — hot-formed, normalized, impact tested at -50°C

  EN 10219 covers S460MH, while EN 10210 covers S460NH and S460NLH.

  S460 Material Grades: S460MH vs S460NH vs S460NLH

  S460MH, S460NH, and S460NLH differ significantly in chemical composition, mechanical properties, size range, and application scenarios. The table below systematically compares key dimensions.

Item S460MH (EN 10219) S460NH (EN 10210) S460NLH (EN 10210)
Forming method Cold-formed + welded Hot-rolled / normalized Hot-rolled / normalized
Delivery condition Thermomechanical rolling (TMCP) Normalized Normalized
Impact temperature -40°C -20°C -50°C
Impact energy requirement 27J (guaranteed by some European mills) 40J 27J
Wall thickness range Typically ≤25mm Up to 120mm Up to 120mm
Dimensional accuracy Tighter Wider Wider
Residual stress Higher Lower Lower
CEV (max) ≤0.46 ≤0.53 ≤0.53
Typical applications Conventional piling, thin-wall large-diameter Thick-wall piles, general low temperature Extreme cold, fatigue-sensitive structures


  Key point: S460MH has a carbon equivalent CEV ≤ 0.46%, providing good weldability. S460NH/NLH, due to normalization, has lower residual stress and better weldability, making them particularly suitable for on-site welding of thick-wall piles and fatigue-sensitive structures.

  S460 Material Chemical Composition (Max %)

Grade C Si Mn P S N CEV (t ≤ 20mm)
S460MH ≤0.16 ≤0.60 ≤1.70 ≤0.035 ≤0.030 ≤0.025 ≤0.46
S460NH ≤0.20 ≤0.60 ≤1.70 ≤0.035 ≤0.030 ≤0.025 ≤0.53
S460NLH ≤0.20 ≤0.60 ≤1.70 ≤0.035 ≤0.030 ≤0.025 ≤0.53

  Data source: EN 10219-1, EN 10210-1, and publicly available product data from European steel mills.

  S460 Material Mechanical Properties

Grade Wall Thickness t (mm) Min Yield Strength ReH (MPa) Tensile Strength Rm (MPa) Min Elongation A₅ (%) Impact Temperature (°C) Impact Energy (J)
S460MH ≤16 460 530–720 17 -40 27
S460NH ≤16 460 540–720 17 -20 40
S460NLH ≤16 460 540–720 17 -50 27

  Note: For circular tubes, when the diameter-to-thickness ratio d/t < 15, the minimum elongation is reduced by 2 percentage points.

  Size Range

  S460MH piling pipes are available in circular, square, and rectangular sections, with circular tubes being the most common. The typical standard product range for cold-formed S460MH pipes is as follows:

Parameter Range
Outer diameter (OD) 42.4 – 323.9 mm (standard product)
Wall thickness (WT) 2.0 – 12.5 mm (standard product)
Fixed length 6,000 – 12,000 mm (conventional)


  Custom engineering ranges can reach outer diameter 1220 mm and above, with wall thickness 25 mm and above. For example, a deep-water wharf project in the Middle East used EN 10219 S460MH spiral welded pipe (SSAW) with specifications of φ1220/1420 × 25 mm, pipe length 44–52 m, and a total weight of approximately 68,000 tons.

  For piling projects requiring thick walls (>25mm) or extra-large diameters, EN 10210 S460NH/NLH hot-formed pipes are recommended, with wall thickness up to 120 mm.

  Dimensional Tolerances and Execution Class:

  Dimensional tolerances for cold-formed S460MH pipes are in accordance with EN 10219-2, which are tighter than those for hot-formed pipes. Piling projects are typically delivered under EN 1090-2 execution class EXC2 or EXC3, requiring corresponding welding procedure qualifications and inspection documents.

  Key Parameters for Piling Pipe Selection

  S460MH piling pipes can be used with either mechanical connections (friction sleeves/threaded) or on-site welded connections. Selection should consider the following factors:

Decision Factor Prefer S355J2H Prefer S460MH
Load requirement Medium load, wall thickness not restricted High load, need to reduce wall thickness or diameter
Driving depth Medium depth Deep driving, need higher resistance to hammer stress
Transport/lifting restrictions No special restrictions Need to reduce single pile weight
Carbon emission target Conventional projects Projects with carbon reduction targets or life-cycle cost sensitivity
Low-temperature environment Above -20°C -40°C (MH) or -50°C (NLH)
Thick-wall requirement Wall thickness ≤25mm Wall thickness >25mm, select NH/NLH


  Key Principle: S460MH is a logical choice when pipe diameter or wall thickness is constrained by the capabilities of transport and piling equipment, or when the project has carbon reduction targets. However, if local buckling of large-diameter piles governs the design, the weight-saving benefits of upgrading the steel grade will be diminished. Selection should begin with load-bearing requirements, integrating buckling analysis and construction equipment capabilities to determine the optimal combination of pipe diameter, wall thickness, and steel grade. Compared to S355J2H, S460MH can reduce steel consumption by approximately 20–30% for the same load-bearing capacity (depending on buckling conditions).
  In European and international piling projects, S355J2H material has long been the default steel grade for steel pipe piles. However, as projects demand higher load-carrying efficiency, lower material consumption, and reduced carbon emissions, S460MH has become the preferred high-strength alternative for large-diameter steel pipe piles and micropiles. S460MH has a minimum yield strength of 460 MPa, approximately 30% higher than S355. For micropiles, S460MH is already the standard steel grade in Nordic countries. Upgrading from S355 to S460MH can reduce CO₂ emissions by approximately 19%.

Related News
Read More >>
Pressure rating of stainless steel seamless pipes Pressure rating of stainless steel seamless pipes
Nov .19.2026
  Stainless steel seamless pipes (SS seamless pipe) are a kind of high-strength and corrosion-resistant pipe material, which is widely used in fluid transportation systems in the petroleum, chemical, pharmaceutical, food and other industries. Different application scenarios require the selection of stainless steel seamless pipes with different pressure ratings.
API 5L Pipe Specification: Line Pipe Grades PSL1 & PSL2 API 5L Pipe Specification: Line Pipe Grades PSL1 & PSL2
Nov .17.2026
API 5L Standard covers seamless steel pipe and welded steel pipe for use in conveying gas, water, and oil in the petroleum and natural gas industries. It includes various grades from Grade B to X70, with different product specification levels (PSL1 and PSL2) to meet different service requirements.
ASTM A53 vs ASTM A106 Carbon Steel Pipe: Key Differences & Selection Guide ASTM A53 vs ASTM A106 Carbon Steel Pipe: Key Differences & Selection Guide
Nov .12.2026
  When selecting carbon steel pipes, ASTM A53, ASTM A106 are three of the most frequently mentioned standards, but their positioning is completely different:
ASTM A53 GR.B ERW Steel Pipe ASTM A53 GR.B ERW Steel Pipe
Nov .10.2026
  ASTM A53 is a Carbon steel pipe standard established by the American Society for Testing and Materials (ASTM). Grade B indicates a material grade with higher tensile strength (≥415 MPa) and yield strength (≥240 MPa). ERW (Electric Resistance Welded) refers to steel pipe manufactured using the electric resistance welding process, as opposed to seamless pipe.