ASTM A106 and ASME SA106 seamless pressure pipe is commonly used in the construction of oil and gas refineries, power plants, petrochemical plants, boilers, and ships where the piping must transport fluids and gases that exhibit higher temperatures and pressure levels.
ASTM A106 and ASME SA106 covers seamless carbon steel nominal wall pipe for high-temperature service. Suitable for bending, flanging and similar forming operations.
NPS 1-1/2″ and under may be either hot finished or cold drawn. NPS 2″ and larger shall be hot finished unless otherwise specified.
Looking for specific post-production services?
Killed steel, with primary melting process being open-hearth, basic-oxygen, or electric-furnace, possibly combined with separate degassing or refining.
Steel cast in ingots or strand cast is permissible.
Hot-finished pipe need not be heat treated.
Cold-drawn pipe shall be heat treated after the final cold draw pass.
| Grade A | Grade B | Grade C | |
| Carbon max. % | 0.25 | 0.30* | 0.35* |
| *Manganese % | 0.27 to 0.93 | *0.29 to 1.06 | *0.29 to 1.06 |
| Phosphorous, max. % | 0.035 | 0.035 | 0.035 |
| Sulfur, max. % | 0.035 | 0.035 | 0.035 |
| Silicon, min.% | 0.10 | 0.10 | 0.10 |
| Chrome, max. % | 0.40 | 0.40 | 0.40 |
| Copper, max. % | 0.40 | 0.40 | 0.40 |
| Molybdenum, max. % | 0.15 | 0.15 | 0.15 |
| Nickel, max. % | 0.40 | 0.40 | 0.40 |
| Vanadium, max.% | 0.08 | 0.08 | 0.08 |
| *Unless otherwise specified by the purchaser, for each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified maximum will be permitted up to a maximum of 1.65% (1.35% for ASME SA106). | |||
The minimum wall thickness at any point shall not be more than 12.5% under the nominal wall thickness specified.
Weight of any length shall not vary more than 10% over and 3.5% under that specified. NOTE — NPS 4 and smaller — weighed in lots. Larger sizes shall be weighed separately by length.
It is industry standard for steel pipe mills to produce A106 pipe to the same OD tolerance of A53 pipe, with a +/- 1% OD tolerance.
| Seamless | |||
| Grade A | Grade B | Grade C | |
| Tensile Strength, min., psi | 48,000 | 60,000 | 70,000 |
| Yield Strength, min., psi | 30,000 | 35,000 | 40,000 |
Inspection test pressures produce a stress in the pipe wall equal to 60% of specified minimum yield strength (SMYS) at room temperature. Maximum Pressures are not to exceed 2500 psi for NPS3 and must stay under 2800 psi for the larger sizes. Pressure is maintained for not less than 5 seconds.
Tensile Test — NPS 8 and larger — either transverse or longitudinal acceptable Smaller than NPS 8 — weighed in lots. Larger sizes — by length. Flattening Test — NPS 2-1/2 and larger. Bending Test (Cold) — NPS 2 and under.
| Degree of Bend | Diameter of Mandrel | ||
| For Normal A106 Uses | 90 | 12 x nom dia. of pipe | |
| For Close Coiling | 180 | 8 x nom dia. of pipe |
Lengths required shall be specified on order. No “jointers” permitted unless otherwise specified. If no definite lengths required, following practice applies: Single Random — 17′ ~ 24′ lengths Double Random — 36′ ~ 44′ lengths
(On Tags attached to each Bundle in case of Bundled Pipe) Rolled, Stamped, or Stenciled (Mfrs. Option) Manufacturer’s name or brand. Length of pipe. A106 A, A 106 B, A 106 C. ANSI schedule number. Hydrostatic test pressures and/or NDE; Weight per foot (NPS 4 and larger) or NH if neither is specified. Additional “S” if tested supplementary requirements.
Orders for material under this specification should include the following, as required, to describe the desired material adequately:
| Quantity | Feet, centimeters, or number of lengths | ||||
| Name of material | Seamless | ||||
| Grade | Grade A, Grade B, or Grade C | ||||
| Manufacture | Hot-finished or cold-drawn | ||||
| Size | NPS or Outside Diameter and Schedule Number of Average Wall Thickness | ||||
| Special outside diameter tolerance pipe | |||||
| Inside diameter tolerance pipe, over 10 in ID | |||||
| Length | Specific or random | ||||
| Supplementary requirements | |||||
| Test Report Required | |||||
| Specification designation | |||||
| Hydrostatic test | |||||
| Special requirements | |||||
*ASTM A 106 grade B Seamless Pressure Pipe
B) Unless otherwise specified by the purchaser, for each reduction of 0.01 % below the specified carbon maximum, an increase of 0.06 % manganese above the specified maximum will be permitted up to a maximum of 1.65 %.
*ASME SA 106 grade B Seamless Pressure Pipe
B) For each reduction of 0.01 % below the specified carbon maximum, an increase of 0.06 % manganese above the specified maximum will be permitted up to a maximum of 1.35 %.
ASTM A106/ASME SA106 Hot Rolled Carbon Steel Seamless Pipes is made by hot rolling and piercing a solid billet through it to leave a hollow tube. The pipe is then shaped to size and heat treated to specification. Seamless pipe is very common and considered a higher grade pipe. Applications include high pressure vessels, nozzles and critical applications requiring highest material integrity. Seamless pipe is also pressure tested to ASTM / ASME specification. Grade "B" signifies "seamless". A106 B seamless pipe is easily weldable using various welding procedures. This makes it preferred choice for pressure piping associated with various Oil, Gas and Industrial application. Seamless pipe is also very common in petrochemical industries for carrying high pressure fluid. Trupply offers seamless pipe for convenient online shopping in various lengths. 22 ft pipe is considered SRL "single random length" and actual length can vary from 19' to 22'.
ASTM A106 Seamless Carbon Steel Pipe for High Temperature Service,It has a maximum carbon content of 0.30% and a maximum manganese content of 1.20%, making it a low-carbon steel with good strength and toughness.
